Seamless or welded
Seamless pipe is made by piercing a solid billet, so it has no weld seam and uniform properties around the circumference. Welded pipe is formed from strip or plate and joined along a longitudinal seam; it is then either left as-welded, or cold-worked and annealed to homogenise the weld zone.
The practical difference is not "strong versus weak". It is where the material is least predictable. In a welded pipe that has not been properly annealed after welding, the seam and its heat-affected zone retain residual stress and, in some grades, sensitised grain boundaries. In seamless pipe, the equivalent variation sits in the wall-thickness eccentricity instead.
Welded pipe becomes the right answer when the diameter is large, the wall is thin relative to diameter, or the length required makes seamless uneconomic. Seamless remains the default for high pressure, small diameter and cyclic service.
How pipe is sized
Stainless pipe is ordered as outside diameter × wall thickness — for example 25.4 mm OD × 1.5 mm WT. Nominal bore designations such as DN25 or NPS 1 are convenience labels inherited from carbon steel practice, and different schedules within the same nominal size carry very different walls.
Two consequences follow. First, a quotation that says only "DN25 stainless pipe" is not a quotation for anything specific. Second, when comparing prices between suppliers, compare the wall thickness and the standard — not the nominal size, and not the price per metre alone.
Which standard applies
| Standard | Covers | Typical use |
|---|---|---|
| ASTM A312 | Seamless and welded austenitic pipe, with eddy-current or hydrostatic testing | Corrosive and high-temperature process piping |
| ASTM A269 | General-service seamless and welded austenitic tubing | Instrumentation, small-diameter process lines |
| ASTM A249 | Welded austenitic tube for heat exchangers and boilers | Heat exchanger and condenser tube |
| ASTM A554 | Welded austenitic ornamental tube | Handrail, furniture, architectural sections |
| EN 10217-7 | Welded stainless steel tubes for pressure purposes | European pressure and process work |
Choosing the wrong standard is the most common specification error in this product. A554 ornamental tube is not pressure-tested and should never appear in a process line; A269 tube is not automatically acceptable where A312 is specified. The standard decides the test regime, and the test regime is what protects the buyer.
Wall thickness and pressure
Pressure capacity scales with wall thickness and allowable stress, and only weakly with grade. Moving from 304 to 316L for corrosion reasons does not compensate for a wall that is 30% under the drawing. This is why the wall thickness belongs in the first line of the enquiry, together with the tolerance class if the application is pressure-critical.
Where the design pressure is not stated, quote the required wall directly rather than naming a schedule — schedules are nominal and their actual walls differ between standards.
Welding and post-weld treatment
Austenitic stainless welds readily, but the weld zone is where corrosion resistance is lost. Heat tint — the coloured oxide left by welding — is chromium-depleted and will pit before the parent metal does. Grinding it off is not equivalent to removing it chemically.
The correct sequence for corrosive service is: weld with low-carbon or stabilised grades, clean mechanically, pickle to remove heat tint and the chromium-depleted layer, then passivate to rebuild the passive film. Where pickling is impossible, a pickling paste on the weld and heat-affected zone is the minimum.
For high-temperature service above roughly 425 °C, the choice shifts to stabilised grades (321, 347) because they resist sensitisation in service rather than only during welding.
What to put on the order
- Grade and product standard, for example "316L to ASTM A312".
- Outside diameter and wall thickness, with tolerance class if pressure-critical.
- Length: fixed, random, or cut to order; and the end finish (plain, bevelled, capped).
- Surface condition: pickled, bright annealed, or polished, and whether the bore must be clean and dry.
- Test and documentation: mill certificate to EN 10204 3.1, hydrostatic or eddy-current test, third-party inspection.
- Packing: bundle pattern, end protection, and marking that carries grade, size and heat number.