ISO certified · CE certified · 5,000 t annual export capacity sdsteel@chunkang.ltd · +86 147 6353 9656
Overview

The same coil, cut to the size the job needs

Color coated sheet is prepainted coil taken through a cut-to-length line. Nothing about the coating changes at that step: the substrate, the metallic coating mass and the paint system were fixed when the coil was painted. What changes is handling. A sheet has four cut edges, a flatness requirement and a packing problem that a coil does not have.

That makes sheet the right form for wall cladding, flashings, trims, appliance panels and signage, where the buyer wants a finished size rather than a roll to feed through a line. It makes coil the right form where the buyer owns the roll former. Choosing between them is a question about the buyer's equipment, not about the material.

We cut to the length on the order, across 600–1,550 mm widths and 0.12–2.0 mm thicknesses, in the same RAL range as the coil. Sheets are stacked and crated so that the painted faces do not rub in transit, which is where most sheet complaints originate.

PPGI sheet in RAL 9006 crated with interleaving paper for export
Cut sheet, RAL 9006, crated with interleaving paper so the painted faces do not rub in transit.
Specification

Sheet dimensions and coating specification

Table 1 — Color coated sheet dimensions and coating build
PropertyRangeNotes
Thickness0.12–2.0 mm0.3–1.0 mm for cladding, flashings and trim
Width600–1,550 mmCut from coil width; no slitting after painting
LengthCut to orderLength and tolerance stated on the order
SubstrateGI (Z50–Z275), GL (AZ30–AZ150), CR, EGZinc for general outdoor, aluminium-zinc for coastal and industrial
Top coat20 µm minimum; 25–40 µm for PVDF and HDPFilm build is quoted alongside the resin, never instead of it
Back coat5–12 µmThicker where the reverse face stays visible
SurfaceGlossy, matte, embossed, wood or stone printPrint finishes follow the same substrate rules
PackingWooden crate, interleaved, edge protectedCrate size follows sheet format and destination handling
Applications

Where cut sheet is the right form

Table 2 — Sheet applications, with the specification that normally wins
ApplicationUsual substrateUsual coating
Wall cladding and facade panelsGL AZ100–AZ150SMP or HDP, 20–25 µm
Flashings, trims and guttersGI Z180–Z275PE or SMP, 20 µm
Appliance and equipment housingsEG or CRPE, thin back coat
Doors, partitions and signageGI Z120–Z275PE, matte or print finish
Coastal or industrial claddingGL AZ150PVDF, 25 µm or more

Sheet is also the form most often ordered as a sample: a small cut from the production coil shows the actual colour and gloss, which a printed swatch cannot. Ask for a cut sample against the RAL number before the coil is painted if colour is contractual.

Cut prepainted sheet in RAL 5005 lifted from a vertical storage rack
RAL 5005 sheet out of the rack: four cut edges, one flatness requirement, one packing problem.
Colours

RAL colours available in sheet form

Sheet follows the coil colour range, including the architectural shades ordered most often.

Table 3 — RAL colours produced routinely, in sheet as well as coil
RALColourTypical use
RAL 3002Carmine redRoofing and facade accents
RAL 3011Red brownIndustrial roofing, weathered-look cladding
RAL 3020Traffic redSignage, safety cladding, steel structures
RAL 5002Ultramarine blueFactory roofing, wall panels
RAL 5005Signal bluePlant buildings, equipment housings
RAL 1004Golden yellowWarehouse cladding, agricultural buildings
RAL 1015Light ivoryResidential roofing, light-commercial facades
RAL 6005Moss greenLandscape-sensitive roofing and cladding
RAL 6010Grass greenAgricultural and sports buildings
RAL 9003Signal whiteClean-room panels, appliance housings
RAL 7038Agate greyModern facade, industrial cladding
RAL 9006White aluminiumHigh-volume architectural roofing and facade
RAL 9005Jet blackPremium facade, feature panels
Coating thickness measured on RAL 9006, 7016 and 5005 sample panels
Film build checked on RAL 9006, 7016 and 5005 panels before the coil is painted.
Buyer questions

Frequently asked questions

What thickness do you cut for wall cladding?

Between 0.3 and 1.0 mm covers most cladding, flashing and trim work. Thinner sheet forms tighter radii without cracking the paint but dents more easily in handling; above 1.0 mm the sheet stops being a cladding material and starts behaving like plate.

How is sheet length decided?

Length is cut to the figure on your order, with the tolerance stated alongside it. Because the sheet comes off a painted coil, length and squareness are set at the shear, so give the length, the tolerance and the quantity in the same line rather than leaving length to be agreed after the coil is painted.

Can sheets be supplied with the protective film left on?

Yes, where the sheet will be handled or formed again on site. The film has to be removed within the interval its manufacturer specifies, because adhesive left in sunlight cures onto the paint and takes the gloss with it. Tell us if the film is for transit only or for site storage, since the two need different adhesives.

Are sheet edges painted?

The cut edge is bare steel with its metallic coating exposed. That is normal and is the reason coating mass matters: zinc or aluminium-zinc around the cut protects a small exposed area sacrificially. Where the edge will be permanently visible in a corrosive atmosphere, the edge should be sealed or the part folded rather than left as a cut.

Which colours are available in sheet form?

The same RAL range as the coil, because the sheet is cut from the same painted coil. That also means colour is controlled at the coil stage: two sheet orders painted from different coils will be close but not identical, so keep one coil batch for one elevation where colour continuity matters.

How is the price of cut sheet quoted?

Per tonne FOB China, at the coil band plus the cut-to-length operation. Zinc mass, paint system and colour move the figure more than the gauge does, so sheet is quoted per tonne rather than per piece. The minimum is 25 tonnes, the payload of one 20-foot container; trial quantities are quoted on request.

Other forms of the same material

Sheet is cut from coil; roofing sheet is roll-formed from coil. The substrate and paint system stay the same across all three.

Request a quotation and a colour sample

Tell us the grade, form, size and quantity. Reply within 24 hours, Monday–Saturday.

Share a drawing or specification sheet by email to sdsteel@chunkang.ltd.

Nothing is submitted automatically. You choose WhatsApp or email on the next step, so the details reach the sales desk exactly as typed. You can also write to sdsteel@chunkang.ltd.

WhatsApp Email Call